Header Ads

How to Configure Static Routing in 3 Router in Cisco Packet Tracer

This is a static routing lab in which we will learn how to configure static routing for a network having three routers inside packet tracer.Here in this  Lab there are  total four network 1.0.0.0/8, 2.0.0.0/8,200.200.200.0/24 and 10.0.0.0/8,172.24.0.0/16,192.168.10.0/24 and three routers.Using cisco packet tracer i have shown static routing configuration using an example lab.So i even if you are new to ccna or networking you can easily learn by reading this article.This article will help you to easily learn static routing configuration.I have designed the topology diagram using cisco packet tracer which will helps you to understand the Lab.I have also assigned the ip address above each devices and interfaces which will guide you throughout the lab.





Static Routing-----------


1st router command


Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!

Router>enable 
Router#configure terminal 
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 10.10.10.1 255.0.0.0
Router(config-if)#no shutdown 
Router(config-if)#exit 
Router(config)#interface serial 0/0
Router(config-if)#ip address 1.1.1.1 255.0.0.0
Router(config-if)#no shutdown 
Router(config-if)#clock rate 64000
Router(config-if)#exit 


2nd router command 


Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!

Router>enable 
Router#configure terminal 
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 172.24.10.1 255.255.0.0
Router(config-if)#no shutdown 
Router(config-if)#exit 
Router(config)#interface serial 0/0
Router(config-if)#ip address 1.1.1.2 255.0.0.0
Router(config-if)#no shutdown 
Router(config-if)#exit 
Router(config)#interface serial 0/1
Router(config-if)#ip address 2.2.2.1 255.0.0.0
Router(config-if)#no shutdown 
Router(config-if)#clock rate 64000

Router(config-if)#exit


3rd router command


Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!

Router>enable 
Router#configure terminal 
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shutdown 
Router(config-if)#exit 
Router(config)#interface serial 0/0
Router(config-if)#ip address 2.2.2.2 255.0.0.0
Router(config-if)#no shutdown 
Router(config-if)#exit 


Static Routing-----

Router0 Static Routing Command


Router(config)#ip route 172.24.0.0 255.255.0.0 1.1.1.2
Router(config)#ip route 200.200.200.0 255.255.255.0 1.1.1.2
Router(config)#ip route 192.168.10.0 255.255.255.0 1.1.1.2



Router1 Static Routing Command


Router(config)#ip route 10.0.0.0 255.0.0.0 1.1.1.1
Router(config)#ip route 192.168.10.0 255.255.255.0  200.200.200.2



Router2 Static Routing Command


Router(config)#ip route 172.24.0.0 255.255.0.0 200.200.200.1
Router(config)#ip route 1.0.0.0 255.0.0.0 200.200.200.1
Router(config)#ip route 10.0.0.0 255.0.0.0 200.200.200.1


YouTube :

How to Configure Static Routing in 3 Router



Powered by Blogger.